Control the set-up of flexographic printing units on a multi-unit flexographic press
Overview
This standard is for flexographic printers with responsibility for setting up flexographic printing units on web presses. The standard involves the set-up of the machine for printed work that meets the quality required by the customer with the minimum of waste materials.
A multi-unit machine is one that prints two or more colours in a single pass through the machine. It includes the make-ready and the identification and correction of associated print faults, that occur during set-up, whether they are caused by machine or materials.
Multi-unit flexographic printing machines have many possible configurations and features. This standard requires a flexographic printer to be able to set up on multiple-unit presses. It is possible that the printer could be working as part of a team. The printer must have a full working knowledge of multi-unit presses, including issues that arise from the transfer of substrate between units.
Practical ability must be demonstrated in setting up the press to produce printed work to a commercially acceptable standard. This must be done on different substrates and covering a sufficient range of printed work to show full competence to set up a multi-colour flexographic machine. This should include a variety of different kinds of images, in the context of multiple units printing process colour and/or combined spot colours.
This standard requires a flexographic printer to be able to set up and maintain flexographic printing units on a web-fed printing machine. The printer needs to have a full working knowledge of flexographic printing units, including issues that arise from the transfer of substrate between units, ink strength, trapping and drying, achieving and maintaining ink densities for inks on different substrates, and colour control.
The printer must be able to set-up multi-colour work. The printer must be able to check and assess the quality of print under correct viewing conditions against an approved proof and make whatever adjustments are necessary to the press to achieve and maintain the quality required. On more modern machines, integral colour control hardware and software is installed, allowing the printer to check continually that ink densities, dot measurements or spectral colour meet recognised standards and/or are consistent with company standards. The printer is required to be familiar with colour standards and how such standards are maintained. If equipment for this purpose is in use in the company, then the printer must be capable of operating and understanding it.
As well as making ready unit(s) for particular jobs, the printer must also be able to undertake routine maintenance of the unit to ensure it prints to an acceptable quality. Often this will be checked with reference to known quality standards.
Performance criteria
You must be able to:
Select and prepare the plate cylinders
- check you have all the details required for the job and approval to start the job
- check you have enough materials of the right type for the job following standard operating procedures
- report to your manager, if the material provided is not correct or sufficient
- check machines and your work area are safe and ready for production
- check the condition of flexographic plates is suitable for production and meets imposition specifications
- fit plates onto plate cylinders following standard operating procedures
- check the cylinder matches the image size following standard operating procedures
- check the gear size matches cylinder size following standard operating procedures
- check the gear size matches image requirements
**
Set up substrate transport system
*
10. select web for production to meet specifications
11. use reel handling equipment in a safe manner
12. position web centrally on reel stands following standard operating procedures
13. web up the press following the web path required for the job following standard operating procedures
14. check reel unwind is meeting the in-feed requirements
15. position web detectors to meet specifications
16. test the substrate transfer system to confirm it runs without breaking following standard operating procedures
17. set impression pressure for the thickness of substrate to be printed
*
Set and adjust the units inking system to suit print profile
*
18. select anilox rollers to meet specifications
19. set doctor blades pressure to meet specifications
20. set pressure between rollers to meet specifications
21. set pressure of roller to plate to meet specifications
22. introduce inks/ink cassettes to printing units following standard operating procedures
23. run ink through the inking system following standard operating procedures
*
Set press to match pass sheet standard
**
24. set, test and adjust impression pressures so clean, even print is produced
25. position images to meet specifications
26. adjust machine settings to meet specifications and quality standards
27. report to your manager if circumstances beyond your control prevent you from producing a pass sheet to the required standard
28. obtain a "pass sheet" that meets company standards
29. identify and rectify faults that occur with machines and consumables
Knowledge and Understanding
You need to know and understand:
Law and regulations
- your legal duties for health and safety in the workplace as defined by the relevant health and safety legislation
- your duties and responsibilities for health and safety as defined by any specific legislation covering your job role
- workplace policies and procedures
- working practices
- hazards and risks in the workplace, their assessment and the action to take to deal with them
- hazards and risks in your own job, their assessment and the action to take to deal with them - including relevant regulations on the safe handling of equipment and materials.
- manufacturer's health and safety requirements relevant to your job
- Personal Protective Equipment used
- how to stop machinery in the event of an emergency
**
Communication
*
10. how to communicate with colleagues, customers and suppliers
*
Workplace policy and practice
*
11. workplace objectives, priorities, standards and procedures
12. the range of work carried out in the workplace
13. the working practices existing in the workplace
*
The identification and assessment of printing options
*
14. the stages in the printing process from pre-press to printed product
*
Time and Resources
*
15. the different types of resource, including labour, materials, machinery
16. the relationship between resource usage and profitability
17. how to maximise productivity
18. the relationship between productivity and competitiveness
*
The operation of equipment
*
19. range of adjustments and settings on flexographic printing units
20. operating practices and procedures for flexographic printing units
21. use of colour control equipment, including densitometers and spectrophotometers
*
Printing
*
22. principles of flexographic printing *
The causes and treatment of common faults
*
23. raw material faults
24. processing (printing) faults
25. machine faults
*
Administrative procedures
*
26. recording and reporting
27. product labelling
*
Environmental
*
28. legal requirements for the classification, storage, carriage and disposal of waste
29. environmental legislation that covers processes in your company
30. existence of any national or international standards on environmental management
*
Quality Assurance and Control
*
31. main features of quality assurance and quality control systems
32. techniques for controlling quality, including inspection, testing, sampling, use of input and output controls
33. equipment for controlling quality in machine printing
34. light standards for viewing and assessing colour print
*
Problem Solving
*
35. types of problems that may need to be solved
36. sources of information
37. techniques for solving complex problems
38. techniques for assessing machine faults
*
Materials
*
39. types and characteristics of paper, board and other commonly used substrates
40. types and characteristics of inks, coatings and coatings
41. how to maintain the quality of materials during storage and handling
*
Proofing
**
42. principal types of proof and their role in the printing process